AR15NEWS.COM – Your AR-15 news source!

AR15NEWS.COM – Your AR-15 news source for all new AR-15 accessories, tactical gear and product reviews!

*Exclusive Intro Price* Cross Machine Tool ZCOMP-L Linear Comp

Posted on January 6th, 2017 by ar15news

Rainier Arms has the exclusive intro offering of the new Cross Machine Tool ZCOMP-L Linear Muzzle Device. The new ZCOMP-L is basically a blast forwarding device with a few small side ports as well as some cool machining. The machining on the outside gives it a similar look to the standard ZCOMP and the mag well grooves CMT is know for. With out outside diameter of just 1.187″ you should be able to tuck a portion of this comp under many rails for a nice clean look.

Cross Machine Tool ZCOMP L Linear comp 1

Cross Machine Tool ZCOMP L Linear comp 1

Cross Machine Tool’s ZCOMP™ LINEAR provides forward directional muzzle blast control desired on rifles with shorter barrels. The outer diameter fluting and front nose cuts not only reduce the overall weight of the device but also blend with the aggressive aesthetic appearance of our Trademark magwell grooves on CMT UHP15 series Lower receivers. Function of the ZCOMP LINEAR muzzle device is equaled by the exceptional visible manufacturing quality & apprearence you expect from Cross Machine Tool products. MADE IN USA.

Features for ZCOMP™ LINEAR 556:
– 1/2 28 RH ID threads
– 1.187″ max diameter x 2.75″ OAL.   Nitride finish
– Weight- 5.5 ozs.
– Caliber- 5.56mm / .223 Remington only
– Rating- Full Auto
– Zero porting on bottom side to reduce ground signature when fired from the prone position
– Zero porting on the center top side to reduce flash sight obstruction through optics/sights
– Minimal side port holes minimzing side blast concussion
– Crush washer included

Features for ZCOMP™ LINEAR .30 :
– 5/8- 24 RH ID threads
– 1.187″ max diameter x 2.75″ OAL.   Nitride finish
– Weight- 5.3 ozs.
– Caliber- 308, 300blkout, 6.5
– Rating- Full Auto
– Zero porting on bottom side to reduce ground signature when fired from the prone position
– Zero porting on the center top side to reduce flash sight obstruction through optics/sights
– Minimal side port holes minimzing side blast concussion
– Crush washer included

If you want to get your hands on the first batch of CMT ZCOMP-L’s to hit the market and get an exclusive intro price on them too, head on over to www.RainierArms.com now. They have both .22 Cal and .30 Cal models in stock and ready to ship.

**NEW** Cross Machine Tool UHPR MOD2 M-LOK Handguards

Posted on December 16th, 2016 by ar15news

If you’re an AR builder, you’d have to be hiding under a rock to not know who Cross Machine Tool is. They started out making billet lower receivers, then added billet uppers, innovative billet lowers with intregrated PDW stock systems, AR-10 receiver sets and muzzle brakes. Most recently they have introduced their UHPR line of handguards. First was the MOD1 which deleted all but the very front of the 12 o’clock picatinny rail. Today the new UHPR MOD2 M-LOK rails are available and they feature a full 12 o’clock picatinny rail section with M-LOK mounting slots at the 3, 6 and 9 o’clock positions. 

Cross Machine Tool CMT UHPR MOD 2 rails

Cross Machine Tool CMT UHPR MOD 2 rails 1

The new Cross Machine Tool UHPR MOD 2 handguards are available in 6.7″, 9.5″, 13.7″ and 15″ lengths. Rainier Arms has secured the exclusive introduction on these rails and is offering them at a limited time introductory price. These rails are a crazy good value with the 6.7″ starting at $138 all the way up to the 15″ which is still just $170. If you’re looking for an awesome new rail for your AR, head on over to www.RainierArms.com and snag one of these new CMT MOD2 rails.

ETS Group Introduces 6 New .40 Cal Glock Mags

Posted on December 16th, 2016 by ar15news

ETS Group Glock mags have been a huge hit ever since their introduction last year. Part of the reason for their popularity is that they cost quite a bit less than an OEM Glock mag and the transparent body looks awesome too. I bought some of the 31rd 9mm Glock mags from ETS a while back to use in my QuarterCircle10 AR9 and they have been awesome. They function flawlessly and are the only mags I have that will reliably lock the bolt back on an empty mag. They currently offer eight different 9mm Glock magazines and now they have added six new .40 Cal Glock magazines. Those new mags are 9rd, 13rd, 16rd, Competition Legal 19rd, Competition Legal 24rd and a 31rd. 

ETS Group 40 Cal Glock Mags

These new ETS Group .40 Cal Glock Mags start at just $16.99 but ETS is offering an introductory discount code which will save you 15% off. Just use the code “ETS40” during checkout at www.ETSGroup.us.

Tyrant Designs MOD ForeGrip (MLOK and KeyMod)

Posted on December 7th, 2016 by ar15news

Tyrant Designs has expanded their grip options to now include the MOD ForeGrip. The MOD ForeGrip features an all metal grip body with polymer straps that are similar in design and looks to their most popular pistol grip called the MOD Grip. The MOD ForeGrip is available in Black, Gray and Red and will definitely add a cool look to your AR. Another cool feature is that you don’t have to pick between MLOK or KeyMod as it will work on both. 

Tyrant Designs MOD ForeGrip 1Tyrant Designs MOD ForeGrip 2Tyrant Designs MOD ForeGrip 2– Durable (polymer straps and aluminum body, near indestructible)
– Interchangeable with M-LOK and KeyMod
– Lightweight- 1.7 oz 
– Beadblasted and Hardcoat anodized Black
– Comfortable (chamfered edges for a smooth feel)
– Temperature variation resistent
– Polymer strap
– Comes with everything needed for installation (screws and allen keys)

 

Rainier Arms has secured the first run of Tyrant Designs MOD ForeGrips and is offering them at an introductory price. Head on over to www.RainierArms.com to order one for yourself. These will ship in about 2 weeks.

**NEW** Ballistic Advantage Complete Uppers

Posted on November 10th, 2016 by ar15news

After using a number of Ballistic Advantage barrels in builds over the last few years I can definitely tell you they make some awesome barrels that somehow stay budget friendly. There have been small comments about Ballistic Advantage Complete Uppers for months now and most of us assumed there would be a few different options. Nobody imagined there would be 44 different configurations available right off the bat. With that many options, you definitely should be able to find exactly what you’re looking for. You get to choose between .223 Wylde, 5.56 NATO and 300BLK calibers, different barrel lengths, different muzzle device options, BCG options, etc. They even come with a cool new rail made by VLTOR specifically for Ballistic Advantage. Details below…

ballistic-advantage-complete-uppers

We are proud to announce, the long-awaited Ballistic Advantage complete uppers are now available with special introductory pricing! The same precision and attention to detail Ballistic Advantage barrels are known for goes directly into these complete uppers.

Our complete uppers feature:
-Your choice of a .223 Wylde, 5.56 NATO, or .300 BLK Ballistic Advantage Hanson Barrel
-VLTOR + BA Freedom Rail w/ KeyMod, manufactured specifically for us by our good friends at VLTOR
-Mil-Spec Flat-top black anodized upper w/ M4 feedramps and T-marks
-Optional VG6 muzzle device
-Optional BCG (Nickel Boron or phosphate)
-Optional charging handle

We are offering 44 different variations to ensure you are outfitted with the correct tool for your type of shooting, from plinking to precision.

Buy Ballistic Advantage Complete Uppers Here! 

I personally run exclusively CMC and Geissele/ALG triggers in my guns. Not because I have to but because they are awesome and I choose to use them. However, this new “Saber” from James Madison Tactical is intriguing purely because of the price point. The Saber is a single stage drop-in trigger with a 3.5-4.0 pound pull weight. Rainier Arms has secured the first run of these triggers at an introductory price of $89.95. I personally have not used one of these triggers but if I wanted to upgrade my stock trigger and couldn’t afford a CMC or Geissele this is something I would consider. 

jmt-saber-single-stage-drop-in-trigger-jmt-ditrigg-by-jmt-77f

With a fast reset, a smoother, crisper, lighter trigger pull, The single-stage trigger group is easy to install.

Features:
–  Single-stage
–  3.5- 4.0 lb. pull weight
–  Quick reset for faster response time between shots
–  Lightened trigger pull with super-crisp release to improve accuracy
–  Curved skeleton trigger function and comfort
–  Self-contained design makes it easy and quick to install with no fine-tuning needed
–  Quality 17-4 Stainless steel hammer, trigger and disconnect
–  Precision CNC and EDM machined from high-grade 6061-T6 aluminum and 17-4 ph SS
–  Contained in JMT’s signature metallic silver anodized aluminum housing
–  Note: The set screw should not be tampered with. Any attempts to modify the trigger will void the warranty.

You can get in on the intro pricing now at www.RainierArms.com.

**Intro Price** Cross Machine Tool CFC 556 ZCOMP

Posted on September 23rd, 2016 by ar15news

Cross Machine Tool has introduced their new CFC 556 ZCOMP muzzle device. The ZCOMP is basically a do-all muzzle device that reduced Flash, Muzzle Rise and Recoil. It is also long enough to be pinned to a 14.5″ barrel bringing it to 16″ OAL and comes predrilled for this purpose. The CFC 556 ZCOMP is being offered through RainierArms at an Intro Price of just $75. Get in on this deal at www.RainierArms.com.

cmt-cfc-556-zcomp-1cmt-cfc-556-zcomp-1cmt-cfc-556-zcomp-1cmt-cfc-556-zcomp-1

Intro Price! $75.00

The CFC 556 (Combat Flash Compensator) A.K.A. the ZCOMP™ is a Hybrid muzzle device.The CFC 556 is designed to reduce and distort visible muzzle flash, reduce muzzle rise & mitigate felt recoil. Function of the CFC 556 muzzle device is equaled by the exceptional visible manufacturing quality & appearance of the muzzle device.

FEATURES
– Manufactured from 17-4 PH Stainless Steel
– QPQ Nitride finished for durability & corrsion protection-standard
– 1/2 28 RH ID threads
– .632″ max diameter
– Surface Hardness-68RC Substrate Hardness-30 RC (QPQ SS only)
– Weight- 2.2 ozs
– Caliber- 5.56mm / .223 Remington only
– Rating- Full Auto
– Zero porting on bottom side to reduce ground signature when fired from the prone position
– Zero porting on the top side center to reduce flash sight obstruction through optics/sights
– Large combustion chamber with ports on each side to aid flash distortion
– Aggressivley Textured front inner tang surfaces to aid flash distortion
– Outer tang styling cuts to match our Trademark magwell cuts on the UHP15 series lower receivers
– 3 forward ports between the tangs to aid flash distortion
– Pre-drilled for pinning to 14.5″ barrel to legal length (pin included)
– Crush washer included (not for suppressor use)
– Made in the USA

https://www.rainierarms.com/cmt-zcomp-combat-flash-compensator

**NEW** Cross Machine Tool CFC ZCOMP – One Week Intro Price

Posted on September 11th, 2016 by ar15news

Cross Machine Tool just released their new CFC ZCOMP muzzle device and are offering it at an outstanding introductory price this week only. The CFC ZCOMP will help reduce muzzle rise, flash and felt recoil while looking pretty sweet too. Check out the details below. Get the ZCOMP at an intro price of $75 at www.CMTTAC.com.

cmt-cfc-5-56-zcomp

The CFC 556 (Combat Flash Compensator) A.K.A. the ZCOMP™ is a Hybrid muzzle device.The CFC 556 is designed to reduce and distort visible muzzle flash, reduce muzzle rise & mitigate felt recoil. Function of the CFC 556 muzzle device is equaled by the exceptional visible manufacturing quality & appearance of the muzzle device.

FEATURES
–  Manufactured from 17-4 PH Stainless Steel
–  QPQ Nitride finished for durability & corrsion protection-standard
–  1/2 28 RH ID threads
–  .632″ max diameter
–  Surface Hardness-68RC Substrate Hardness-30 RC (QPQ SS only)
–  Weight- 2.2 ozs
–  Caliber- 5.56mm / .223 Remington only
–  Rating- Full Auto
–  Zero porting on bottom side to reduce ground signature when fired from the prone position
–  Zero porting on the top side center to reduce flash sight obstruction through optics/sights
–  Large combustion chamber with ports on each side to aid flash distortion
–  Aggressivley Textured front inner tang surfaces to aid flash distortion
–  Outer tang styling cuts to match our Trademark magwell cuts on the UHP15 series lower receivers
–  3 forward ports between the tangs to aid flash distortion
–  Pre-drilled for pinning to 14.5″ barrel to legal length (pin included)
–  Crush washer included (not for suppressor use)
–  Made in the USA

www.CMTTAC.com

**NEW** Phase 5 Tactical Sloped Quick Disconnect End Plate

Posted on September 6th, 2016 by ar15news

Pretty sure I have a QD End Plate on just about every rifle I’ve ever built but they all require you to get your big (sometimes gloved) hands into this tiny area to attach/detach the QD sling swivel. The new Sloped Quick Disconnect End Plate (SQD-EP) addresses that issue and gives you a nice ambi QD sling mount. It also covers up some of the castle nut for a cleaner look. I will definitely pick one of these up for my next build and see how it goes. Looks like a great design. Read more about it and check out the pics below.

 P5T SQD-EPP5T SQD-EP 3

The Phase 5 Sloped Quick Disconnect End Plate (SQD-EP) was designed to replace the standard AR15/M4 carbine end plate. While still meeting the requirements of the original design, the SQD-EP is lighter and QD Swivel compatible.

PROUDLY MADE IN THE USA FROM USA RAW BILLET 7075-T6 ALUMINUM.

– Compatible with mil-spec carbine reciever extensions, commercial-spec reciever extensions, and all Phase 5 Pistol Buffer Tubes on nearly all AR15/M4/.308 AR Variant lower recievers.
– Lightweight and sturdy 7075-T6 billet aluminum construction is about 80% stronger than 6061-T6 aluminum.
– Uses a standard AR15/M4 carbine Lower reciever extension castle nut (not included).
– Accepts all push button QD swivels and QD slings.
– QD mount is at a 30 Degree angle from the lower reciever to allow a 360 Degree rotation for ambidextrious use.
– Lighter than the standard stamped steel reciever extention end plate (0.39 oz vs 0.48 oz.

The SQD-EP is in-stock and shipping now. Normally I would just link to the manufacturer  (Phase5WSI.com) for new product announcements but I also just noticed that these are available at an intro price at www.RainierArms.com now through 9/15/16. 

Glock Ambi Mag Release Designed for Right Handed Shooters

Posted on July 18th, 2016 by ar15news

I’ve always shot my Glocks a lot but ever since I built my Quarter Circle 10 9mm AR I’ve been shooting them even more. Recently I had the opportunity to add the Rainier Arms MARS (Magazine Advanced Release System) ambi mag release in my G17. If you’re thinking….”I shoot right handed so I don’t need an ambi mag release” keep reading.

Rainier Arms MARS ambi mag release glock 1

Rainier Arms MARS ambi mag release glock

Typically ambi controls are designed to benefit left hand shooters but this ambi mag release was actually designed to help right hand shooters. On a Glock, many right handed shooters have to break their grip to reach their thumb far enough to activate the standard mag release consistently. Left handed Glock shooters typically use their Index or Middle finger to use the mag release which is actually better as it does not require that you change your grip on the gun.

The MARS fixes this by adding an ambi mag release on the right side so right handed shooters can now use their Index or Middle finger to release the magazine. They have also extended the mag release button on the left side making it even easier for left handed shooters to access with their Index or Middle finger. 

rainier-arms-mars-magazine-advanced-release-system-for-glock-ra-mars-g3-a41

Whether you shoot predominantly Left OR Right hand doesn’t matter with the Rainier Arms MARS. Its a great upgrade for any Glock pistol shooter and has functioned flawlessly in my G17. Rainier Arms has just made these available for sale on their website and are offering them at an introductory price. Regular price is $66.45 but the Intro Price is just $59.95. If you happen to be a Rainier Arms APEX member, your price is just $49.95. Head on over to www.RainierArms.com to snag one at the intro pricing. 

There are quite a few “PDW” style stocks on the market for the AR-15 right now. Most, if not all of them, use a shorter buffer tube setup with a modified buffer and spring to shorten the overall length of the stock which is what makes them great for use on a PDW (Personal Defense Weapon). Unfortunately, most of the PDW stocks on the market add multiple steps to disassemble the weapon and in some cases even require that you use a specific BCG. There are very few options out there that are truly drop-in setups that allow you to “shotgun” your upper and use any BCG you want. The new X Products R.O.C. (Rapid Operation Carbine) PDW Stock does just that allowing you to use any BCG you want “shotgun” your upper with out removing the front pivot pin or locking the buffer back. A couple of additional things to note is that it weights just 17.6 ounces and can be used on 9mm ARs, Direct Impingement and Piston systems. What’s even crazier…the price point is $350 with an intro price of just $289.95.

Check out the pics and details below. These are in-stock now at www.XProducts.com.

x-products-roc-rapid-operations-carbine-stock-ar-15-pdw-cqb-stock-dissasembled_0

The X Products R.O.C. (Rapid Operation Carbine) Stock is the most adapted PDW stock design available in the smallest package. Ergonomic, easy to use and designed for a low profile, compact platform. The X Products ROC Stock set will fit on any Mil-Spec AR-15/M4 & HKMR556, HK 416 lower receiver. Tested and designed to be used with nearly ALL commercial and LE/Mil ammunition types. Easy to install and durable. Its 5 adjustment points give the shooter maximum versatility. To top it off, the R.O.C. Stock does NOT require a proprietary bolt carrier or special components. Use a true drop on PDW stock set solution for your HK 416C or AR/M4 PDW project. Made 100% in the USA.

x-products-roc-rapid-operations-carbine-stock-ar-15-pdw-cqb-stock-on-sbr-rifle-collapsed_01 x-products-roc-rapid-operations-carbine-stock-ar-15-pdw-cqb-stock-on-sbr-rifle_0

– 5 position stainless steel nitrided rails
– 7075 hard anodized aluminum body
– Stainless steel tungsten filled buffer 1.8 oz in total weight
– Chrome silicon flat wire buffer spring
– Extended castle nut
– Ambi sling attachment backplate
– All steel locking mechanism
– Works will all mil-spec AR15, M4 & M16 BCG
– Works with both DI & Gas Piston systems
– Shorter than an standard M4 stock when collapsed
– Total weight of stock, spring and buffer set 17.6 oz
– Fully collapsed 5 3/8″ long, fully extended 11″

CORE Rifle Systems Muzzle Brake

Posted on June 16th, 2016 by ar15news

CORE Rifle Systems just released their new CORE Muzzle Brake and I have to admit, it looks pretty awesome. It features a dual chamber design to reduce recoil and 4 vertical ports to compensate for muzzle rise which will help with faster follow up shots. Right now they are offering a special introductory price. Normal price is $89.99 but they are intro’ing them at just $59.99 for a short time. You can watch a video of it in action here: https://www.facebook.com/118762944846071/videos/1103136773075345/

Head on over to www.CORE15Rifles.com and snag one now. 

Core 15 rifles CORE muzzle brake

V7 Enlightened Lithium-Aluminum Lightweight AR15 Lower

Posted on May 17th, 2016 by ar15news

If you follow V7 Weapons at all, you know that they are all about reducing excess weight. They make all kinds of lightweight AR parts such as rails, barrel nuts, takedown pins, bolt catch, gas blocks and even barrels. Now they are introducing an awesome lightweight billet AR15 lower receiver made from Lithium-Aluminum. This lower receiver weighs in at just 6.4 ounces which is super light. And we’re not talking about your typical forged style lower, this is a billet style with a built in winter trigger guard and some pretty cool looking lines. 

RainierArms-v7-enlightened-lithium-aluminum-lowers-ar15 2RainierArms-v7-enlightened-lithium-aluminum-lowers-ar15 1RainierArms-v7-enlightened-lithium-aluminum-lowers-ar15 3

ENLIGHTENED 2055 LITH/ALUM AR-15 LOWER RECEIVER
–  BILLET AR-15 LOWER RECEIVER
–  CONSTRUCTED FROM ADVANCED 2055 LITHIUM/ALUMINUM
–  TYPE III HARDCOAT ANODIZE
–  WEIGHS 6.4 OZ
–  SHIPS WITH QD ENDPLATE (7075 T6)
–  ADVANCED 2055 LITHIUM ALUMINUM ALLOY IS LIGHTER, STRONGER, MORE RIGID & CORROSION RESISTANT THAN STANDARD 7075 T6
–  MIL SPEC COMPATIBLE
–  MADE IN THE USA
–  100% LIFETIME WARRANTY

If you’re building a lightweight AR, this might be the perfect lower for you and if you want to be one of the very first people to get your hands on one, there’s only one place to get them. Get in on the exclusive intro pricing now at www.RainierArms.com.

Faxon Firearms “Gunner” Ultra-Light Bolt Carrier Group

Posted on April 28th, 2016 by ar15news

When looking to reduce felt recoil in an AR-15 (there isn’t a ton but there’s enough), one route you could go is to go with a lightweight Bolt Carrier Group. Lightweight BCGs are largely used in competition rifles like those used 3-Gun where the lighter the recoil the better for fast followup shots, etc. Faxon Firearms is already very well know for their successful ARAK-21 self contained piston upper and massive selection of barrels but noticed some issues with other lightweight BCGs and decided to make their own. Check out the all new Faxon Firearms “Gunner” Ultra-Light BCG and intro pricing info below.

faxon-gunner-bcg-ultra-light-bolt-carrier-groups-ff556bcgcnitride-lw-by-faxon-firearms-140

When looking at lightweight bolt carrier groups, we were unsatisfied with what the market had to offer. Seeing a capability gap, we set out to create a bolt carrier group that could live up to the GUNNER name with no compromise in strength or function. We set specifications that would allow no compromise:

1. Lightest Weight Possible (8.32 Ounces Complete, 6.24 Ounces Carrier & Key Only)
2. MIL-SPEC Materials & Finishes or Better!
3. Forward Assist Serrations
4. Compatible with Dust Covers
5. Maintains Full-Auto Trip Sear for full-auto and the new multi-stage trigger functionality
6. Looks Amazing

faxon-gunner-bcg-ultra-light-bolt-carrier-groups-ff556bcgcnitride-lw-by-faxon-firearms-140

Matching our barrels, we selected the QPQ method of Salt Bath Nitride for all the carriers components. By coating all parts, the carrier’s natural slickness is increased markedly requiring less gas and pressure to operate. Further, the QPQ SBN process seals components against corrosion while making them fantastically wear resistant.

faxon-gunner-bcg-ultra-light-bolt-carrier-groups-ff556bcgcnitride-lw-by-faxon-firearms-140

faxon-gunner-bcg-ultra-light-bolt-carrier-groups-ff556bcgcnitride-lw-by-faxon-firearms-140

As a testament of our trust, the carriers are all laser-engraved with the Faxon Shield after passing all Quality inspections.

Detailed Spec:

Bolt:
– 9310 Tool Steel Construction (Stronger than C158)
– Full MIL-SPEC Heat Treatment
– Shot Peened to MIL-SPEC
– Magnetic Particle Inspection (MPI)
– Back of Lugs Chamfered for Reliability
– Spring, Insert, & “Crane” O-Ring Installed
– QPQ – Salt Bath Nitrided

Extractor:
– S7 Tool Steel Construction
– Fully Heat Treated
– Shot Peened Per MIL-SPEC
– QPQ – Salt Bath Nitrided

Carrier & Key:
– Carrier: MIL-SPEC 8620 Steel Material
– Key: 4140 Steel Material
– Fully Heat Treated
– Forward Assist Serrations
– M16 (FULL-AUTO) Compatible
– Grade 8 Fasteners
– Fully & Properly Staked Key, Permatex Sealed
– QPQ – Salt Bath Nitrided
– Weight w/ Key (Not Bolt or any Pins): 6.32 Ounces

Cam Pin:
– 4140 Pre-Hardended Steel Material
– QPQ – Salt Bath Nitrided

The very first run of the all new Faxon Firearms “Gunner” Ultra-Lightweight Bolt Carrier Group is being offered at an introductory price through …. yup, you guessed it …. Rainier Arms. There are currently less than 35 of these available at the introductory price of $199.99. Get one now at www.RainierArms.com

RISE Armament Ripper Billet Lower Receiver

Posted on April 18th, 2016 by ar15news

You may have heard the name RISE Armament before. They make a pretty sweet looking drop-in trigger and now they make a pretty sweet looking billet lower receiver. Their new Ripper billet lower features milled pockets and lightening cuts pretty much wherever they could do them without making it a skeletonized lower. The result is a unique design and a weight of just 5.6 ounces which is pretty light for a billet lower considering most billet lowers weight between 8 and 11 ounces. Check out this sweet lower and get in on the intro pricing.

RISE Armament Ripper Billet Lower 1RISE Armament Ripper Billet Lower 1RISE Armament Ripper Billet Lower 1RISE Armament Ripper Billet Lower 1

One of the lightest full aluminum billet lower on the market at 5.6 oz!!

Designed and engineered for those who never settle, the RISE Armament Ripper Billet Lower Receiver has a sleek, streamlined design that emphasizes form as much as function. Features include a flared magwell and oversized trigger well.

–  Precision CNC machined from 7075-T6 billet aluminum
–  Flared magwell opening
–  Oversized trigger well
–  Specialized milled pockets for extra weight reduction
–  Multi caliber marking
–  Mil-spec component compatible
–  MIL-A-8625F, Type III, Class 2, hard anodized flat black finish
–  Manufactured in RISE Armament’s Oklahoma facility according to strict AS9100 aerospace  requirements, which are more stringent than standard gun manufacturing requirements
–  Backed by RISE Armament’s 100% product guarantee and lifetime manufacturing warranty
–  Designed and made 100% in Broken Arrow, Oklahoma, U.S.A.
–  Weight 5.6oz

https://www.rainierarms.com/rise-armament-ripper-billet-ar-15-lower-receiver

Navigation

  • PLEASE CHECK OUT OUR SITE SPONSORS

    Weapon OutfittersPhase 5 TacticalClick here to become an AR15NEWS Partner556 TACTICAL - CUSTOM BUILT AR15 ASSAULT RIFLESHexmag AR-15 MagazinesNevada AmmunitionTombstone Tactical - Tactical firearms and accessories!Blacklist IndustriesSpecial Ops TacticalOnly The Best FirearmsTyrant Designs - Recreating InnovationGround Zero Precision80% Lower ReceiversFranklin Armory Binary Firing SystemBravo Company USASpecializing in high end AR15s/M16s, parts & accessoriesFUTURE OF NIGHT VISION & THERMAL IMAGING


Copyright © 2009 AR15NEWS.COM – Your AR-15 news source!.